DSC 9047 INSTALLATION MANUAL PDF

These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accord- ance with the instructions, may cause harmful interference to radio com- munications. However, there is no guarantee that interference will not occur in a particular installation. This booklet is available from the U. Government Printing Office, Washington D.

Author:Daijind Meztizilkree
Country:Brunei Darussalam
Language:English (Spanish)
Genre:Finance
Published (Last):24 April 2006
Pages:15
PDF File Size:16.88 Mb
ePub File Size:8.30 Mb
ISBN:561-7-63814-490-1
Downloads:37912
Price:Free* [*Free Regsitration Required]
Uploader:Akitilar



These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accord- ance with the instructions, may cause harmful interference to radio com- munications. However, there is no guarantee that interference will not occur in a particular installation. This booklet is available from the U.

Government Printing Office, Washington D. On the side of this equipment is a label that contains, among other information, a product identifier. If requested, this number must be provided to the Telephone Company. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant.

See installation instructions for details. Excessive RENs on a telephone line may re- sult in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five 5.

To be certain of the number of devices that may be connected to a line, as de- termined by the total RENs, contact the local Telephone Company. The digits represented by are the REN without a decimal point e. For earlier products, the REN is separately shown on the label.

But if advance notice is not practical, the Telephone Company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. Changes in Telephone Company Equipment or Facilities The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment.

If this happens the Telephone Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the prob- lem is solved. This equipment is of a type that is not intended to be re- paired by the end user.

Contact the state public utility commission, public service commission or corporation commission for information. Alarm dialling equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment telephone, answering system, computer modem, etc.

To do so, alarm dialling equipment must be connected to a properly installed RJX jack that is electrically in series with and ahead of all other equipment attached to the same tele- phone line. Proper installation is depicted in the figure below. If you have any questions concerning these instructions, you should consult your tel- ephone company or a qualified installer about installing the RJX jack and alarm dialling equipment for you.

The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of de- vices subject only to the requirement that the sum of the RENs of all the devices does not exceed five. General Warning The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network.

It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecoms network services. Reverse Numbering decadic signalling Decadic signalling should not be used as it is being progressively phased out of the network.

Line Grabbing Equipment This equipment is set up to carry out test calls at pre-determined times. Such test calls will interrupt any other calls that may be set up on the line at the same time. The timing set for such test calls should be discussed with the installer.

The timing set for test calls from this equipment may be subject to drift. If this proves to be inconvenient and your calls are interrupted, then the problem of timing should be discussed with the equipment installer. Line Feed to Other Devices During dialling, this device unit does not provide DC voltage to the series port connection and this may cause loss of memory functions for the terminal devices local telephone connected to T-1, R

HIPERTROFIA DEL PILORO EN PEDIATRIA PDF

DSC powerseries 9047 Quick Start Manual & Installation Manual

Akinogul TL R — V4. No Product PC v2. Function Keys [ ][6] — User Functions Press [ ][6] followed by the Master Code, then press the number corresponding to the following functions or scroll to the desired option, then press [ ]. The product is labeled with the A-tick compliance manuual. PC manual de instalacion v2. Programming Work Sheets 7. Technical Library Tyco digital security control instruction manual 19 pages.

ARMY DTMS USER MANUAL PDF

DSC 9047 PROGRAMMING MANUAL PDF

Power Power PC v1. Template Programming Template programming allows the Installer to quickly program the minimum functions required for basic operation. PowerSeries Troubleshooting Guide — English. Wireless Device Enrollment Before a wireless device can be recognized by the security system, it must be enrolled. Install Manual — PC — v1. Page 9 Section 2: Device Enrollment must be performed close to the alarm system. Wireless Device Enrollment — See Section 2 of this manual.

Related Articles